Datamax E4203 User Manual Page 39
- Page / 176
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Extended System Commands
E-Class DPL Programmer’s Manual 29
STX KC Get Configuration
This command returns the configuration of the printer. The form of the returned data is similar to that
of a Configuration Label. This command should be parsed by KEYWORDS, not Character
POSITIONS. Each line is terminated by a CR (0x0d) & LF (0x0a). Datamax will make every effort
to keep Keyword consistent.
Syntax:
<STX>KC<CR>
Printer response:
XXX NOT SET 00, 0000 00:22 000
VER: E4304 - 04.06 08/24/01
BOOT 83-2329-04A
CODE 83-2325-04F
FONT 83-2337-01A
CPLD 59-2157-01C
INTERNAL FLASH MODULE PRESENT
SYSTEM RAM CHECKS____ GOOD
SYSTEM RAM SIZE___ 2015 KBYTES
SYSTEM RAM AVAIL__ 1244 KBYTES
REG POWER SUPPLY__ YES
CONFIGURATION
DIRECT THERMAL
SERIAL PORT SELECTED
9600;8 BITS
EDGE
CONT FORM LENGTH__ 0
PRESENT ADJUST____ 127
SOP ADJUST________ 127
TOF LOW___________ 0 0
TOF DELTA_________ 10 10
TOF GAIN__________ 12 10
OOS MAXVOLT_______ 3 3
LABEL ALIGNMENT___ AUTO
ALIGN LENGTH______ 460
STOP LOCATION_____ PEEL
INPUT VALUES
PAPER_____________ 0
POT_______________ 255
TRAN______________ 250
REFL______________ 0
RIBN______________ 116
TEMP______________ 52
VOLT______________ 214
COUNTER INFORMATION
ABSOLUTE VALUES 1- 1-1995
LENGTH____ 2065 INCHES
TIME______ 62 HOURS
RESETABLE VALUES 1- 1-1995
LENGTH____ 2065 INCHES
TIME______ 62 HOURS
MEMORY CONFIGURATION
INTERNAL MODULE______ 15
SCALABLE FONTS_______ 32
LABEL SIZE 0416:02157 IN
END OF LIST
STX Kc Set Configuration
This command, equivalent to using other system commands followed by the <SOH>U and intended
for easily configuring a custom setup not dynamic configuration changes, specifies the Power-up
Configuration parameter values for the printer. The printer will reset upon completion of a command
stream containing parameter value (e.g., memory configuration, label width, etc.) changes; no
commands should be sent until this reset is complete. The following are highlights of this command:
• These parameter values do not affect the factory default settings of the printer.
• When separated by a semi-colon (;), multiple parameter values included in a single command
stream.
• All values are stored in Flash memory and remain in effect until new values are received or until
factory defaults are restored.
• If system commands are sent that override the Power-up Configuration value(s), the Power-up
Configuration value(s) will be restored the next time the printer is powered ‘on’ or reset.
• The parameters are the same as those found in the Setup Menu.
Note: Illegal or out of range parameter values may have unpredictable results.
- Programmer’s Manual 1
- Part Number: 88-2265-01 2
- Revision: D 2
- Table of Contents 3
- Appendix A 8
- Appendix B 8
- Appendix C 8
- Getting to Know the Printer 13
- Control Codes 15
- Immediate Commands 17
- SOH B Toggle Pause 18
- SOH C Stop/Cancel 18
- SOH D SOH Shutdown 18
- SOH E Send Batch Quantity 19
- SOH F Send Status Byte 19
- System-Level Commands 21
- STX d Set Double Buffer Mode 23
- STX e Select Edge Sensor 24
- STX F Form Feed 24
- STX G Print Last Label Format 24
- STX I Image Downloading 25
- STX k Test RS-232 Port 26
- STX m Set Metric Mode 27
- STX o Cycle Cutter 28
- STX p Controlled Pause 28
- STX Q Clear All Modules 29
- STX q Clear Module 29
- STX S Set Feed Speed 29
- STX s Set Single Buffer Mode 30
- STX T Print Dot Pattern Label 30
- STX t Test DRAM Memory Module 30
- STX X Set Default Module 34
- STX x Delete File from Module 35
- STX Y Output Sensor Values 35
- STX y Select Font Symbol Set 36
- STX z Pack Module 36
- Extended System Commands 37
- STX Kb Backfeed Time Delay 38
- STX KC Get Configuration 39
- STX Kc Set Configuration 39
- STX KD Database Configuration 43
- STX KE Character Encoding 44
- STX Kf Set Present Distance 46
- Label-Formatting Commands 49
- A Set Format Attribute 50
- C Set Column Offset Amount 51
- F Font Attributes 53
- H Select Heat Setting 55
- M Select Mirror Mode 55
- P Set Print Speed 56
- Q Set Print Quantity 57
- R Set Row Offset Amount 58
- S Set Slew Speed 59
- Embedding 62
- ^ Set Count by Amount 64
- STX T Print Time and Date 65
- Font Loading Commands 67
- *c###E Character Code 68
- (s#W Character Download Data 68
- Generating Label Formats 69
- Generating Records 70
- The Structure of a Record 70
- TheHeaderFields 71
- Record Structure Types 73
- Width Multiplier 76
- Height Multiplier 76
- (continued) 82
- 10K OHM 1/4 WATT 83
- ‘C’ Language Program 84
- ASCII text file 84
- VB Application Generating DPL 85
- Appendix D 100
- Appendix E 101
- (E2) ISO 8859/2 Latin 2 Set 102
- (E5) ISO 8859/5 Latin 5 Set 102
- (LG) Legal Symbol Set 103
- 0123456789ABCDEF 106
- (VU) Ventura US Symbol Set 108
- Appendix F 111
- Appendix G 113
- W1z / W1Z: MicroPDF417 137
- Appendix H 141
- Specifications (optional) 142
- Standard internal fonts 142
- Appendix I 143
- Character Map Selection 145
- Appendix J 147
- Appendix K 149
- Appendix L 151
- Table L-1 152
- Appendix M 153
- Figure M-2: Sample Label 154
- Appendix N 155
- Appendix O 157
- ILPC-KANJI Option 158
- Appendix H for details) 158
- Appendix P 163
- Appendix Q 165
- Appendix R 167
- Glossary 169
Related products and manuals for Label printers Datamax E4203
Label printers Datamax PE User Manual
(100 pages)
(100 pages)
Label printers Datamax H-4606X Operator's Manual
(186 pages)
(186 pages)
Label printers Datamax H-4310 Specifications
(20 pages)
(20 pages)
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.480 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals