Datamax E4203 User Manual Page 42
- Page / 176
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Extended System Commands
32 E-Class DPL Programmer’s Manual
Present Adjust – Fine-tunes the label stop position (see notes below).
Serial Port Configuration – This command is followed by the port ID, always ‘A’ (i.e., SPA)
then by the configuration parameter and value of Baud or Data Bits:
Baud Rate – The SPABnn command sets the baud rate for the printer serial port, where nn
may be any of the following:
Bnn Baud Rate (Bits Per Second)
12 1200
24 2400
48 4800
96 9600
19 19200
38 38400
Sample: <STX>KcSPAB38<CR>
The above sample sets the printer serial port baud rate to 38400 BPS (the host computer
communications setup is expected to be the same) and has the same effect as using the Setup
Menu.
Data Bits – The <STX>KcSPADn command selects either 7 or 8 data bits, where n may be
either of the following:
Dn Data bits (word length)
77
88
Sample: <STX>KcSPAD8<CR>
The above sample sets the printer serial port to receive eight-bit words (the host computer
communications setup is expected to be the same) and has the same effect as using the Setup
Menu.
SOP Adjust – Fine-tunes the label Start Of Print position (see note below).
Stop Location
–Configures the printer for all standard label present positions, as follows:
Setting Stop Location
Host Provides backward compatibility for users engaging the cutter or Present Sensor to
achieve present distances. The stop location (present distance) may be controlled
dynamically by the host using the <STX>f or <STX>Kf commands. This selection
has the same effect as <STX>KD Ignore Host Distance bit value 0.
Peel Sets the stop location to approximately 2 mm behind the peel bar edge, a nominal
peel position. The Present Sensor status and this setting are independent.
Cut Sets the stop location to a nominal cut position. For die-cut media, the position is just
following the end of the label. The cutter status and this setting are independent.
Cover Sets the stop location to that of the tear bar on the printer cover.
None Sets the stop location to the start of the next label, equivalent to setting the
<STX>KD Ignore Host Distance bit value 1.
Note: The Peel, Cut, Cover, and None settings prevent host commands from affecting start
of print (<STX>O) and stop position (<STX>f, <STX>Kf) commands from being
honored. All stop locations can be adjusted with PRESENT ADJUST.
- Programmer’s Manual 1
- Part Number: 88-2265-01 2
- Revision: D 2
- Table of Contents 3
- Appendix A 8
- Appendix B 8
- Appendix C 8
- Getting to Know the Printer 13
- Control Codes 15
- Immediate Commands 17
- SOH B Toggle Pause 18
- SOH C Stop/Cancel 18
- SOH D SOH Shutdown 18
- SOH E Send Batch Quantity 19
- SOH F Send Status Byte 19
- System-Level Commands 21
- STX d Set Double Buffer Mode 23
- STX e Select Edge Sensor 24
- STX F Form Feed 24
- STX G Print Last Label Format 24
- STX I Image Downloading 25
- STX k Test RS-232 Port 26
- STX m Set Metric Mode 27
- STX o Cycle Cutter 28
- STX p Controlled Pause 28
- STX Q Clear All Modules 29
- STX q Clear Module 29
- STX S Set Feed Speed 29
- STX s Set Single Buffer Mode 30
- STX T Print Dot Pattern Label 30
- STX t Test DRAM Memory Module 30
- STX X Set Default Module 34
- STX x Delete File from Module 35
- STX Y Output Sensor Values 35
- STX y Select Font Symbol Set 36
- STX z Pack Module 36
- Extended System Commands 37
- STX Kb Backfeed Time Delay 38
- STX KC Get Configuration 39
- STX Kc Set Configuration 39
- STX KD Database Configuration 43
- STX KE Character Encoding 44
- STX Kf Set Present Distance 46
- Label-Formatting Commands 49
- A Set Format Attribute 50
- C Set Column Offset Amount 51
- F Font Attributes 53
- H Select Heat Setting 55
- M Select Mirror Mode 55
- P Set Print Speed 56
- Q Set Print Quantity 57
- R Set Row Offset Amount 58
- S Set Slew Speed 59
- Embedding 62
- ^ Set Count by Amount 64
- STX T Print Time and Date 65
- Font Loading Commands 67
- *c###E Character Code 68
- (s#W Character Download Data 68
- Generating Label Formats 69
- Generating Records 70
- The Structure of a Record 70
- TheHeaderFields 71
- Record Structure Types 73
- Width Multiplier 76
- Height Multiplier 76
- (continued) 82
- 10K OHM 1/4 WATT 83
- ‘C’ Language Program 84
- ASCII text file 84
- VB Application Generating DPL 85
- Appendix D 100
- Appendix E 101
- (E2) ISO 8859/2 Latin 2 Set 102
- (E5) ISO 8859/5 Latin 5 Set 102
- (LG) Legal Symbol Set 103
- 0123456789ABCDEF 106
- (VU) Ventura US Symbol Set 108
- Appendix F 111
- Appendix G 113
- W1z / W1Z: MicroPDF417 137
- Appendix H 141
- Specifications (optional) 142
- Standard internal fonts 142
- Appendix I 143
- Character Map Selection 145
- Appendix J 147
- Appendix K 149
- Appendix L 151
- Table L-1 152
- Appendix M 153
- Figure M-2: Sample Label 154
- Appendix N 155
- Appendix O 157
- ILPC-KANJI Option 158
- Appendix H for details) 158
- Appendix P 163
- Appendix Q 165
- Appendix R 167
- Glossary 169
Related products and manuals for Label printers Datamax E4203
Label printers Datamax PE User Manual
(100 pages)
(100 pages)
Label printers Datamax H-4606X Operator's Manual
(186 pages)
(186 pages)
Label printers Datamax H-4310 Specifications
(20 pages)
(20 pages)
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals