Datamax A-Class Operator's Manual download pdf (Page 43)

A-Class 29

3.4 Loading Media



Note: At default settings, a Buzzer will sound when the Access Cover is raised. To disable this function see

Section 4.2.5, System Settings



Buzzer.

Load media as follows:

1. Open the Access Cover and raise the Head Lift Lever.

2. Route the Media between the Media Posts, through the Media Sensor, over the Peel Bar, and out of

the printer, as shown below.

Head Lift Lever

Media Posts

Media Sensor

Access Cover

Media

Peel Bar

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 179 180

Operator’s Manual 1
Contents 9
The User Interface 10
Adjustments and Maintenance 11
Troubleshooting 12
Appendix A 13
Appendix B 13
Appendix C 13
Appendix D 13
Overview 15
1.1 About the Printer 15
1.1.1 Standard Features 16
A-Class 3 17
A-Class 5 19
*Optional feature 21
1.3.1 Right Hand Models 22
1.3.2 Left Hand Models 23
2.1 Unpacking the Printer 25
Getting Started 25
2.1.1 Contents 26
A-Class 13 27
HOST SETTINGS in 28
3.2 Mounting Requirements 29
A-Class 17 31
Mounting Holes 32
3.3 Connecting the Printer 33
10101010 35
Serial Port A 35
Aux Serial 35
Main Logic Card 36
A-Class 23 37
Network Cable 38
DMXNet Card 38
RJ45 Connector 38
Status Indicators 38
A-Class 25 39
26 A-Class 40
3.3.3 Power Connections 41
3.4 Loading Media 43
Release Lever 44
Media Guide 46
Locking Post 47
34 A-Class 48
3.6 Loading Ribbon 49
3.6.1 Removing Ribbon 49
36 A-Class 50
A-Class 37 51
38 A-Class 52
4.1.1 Ready Mode 54
4.1.2 Menu Mode 55
MENU WINDOW 56
SAVE CHANGES? 56
4.1.3 Test Mode 57
Key Labels 58
4.1.4 MCL Mode 59
4.2 The Menu System 60
A-Class 47 61
4.2.2 Media Settings 62
4.2.3 Print Control 63
50 A-Class 64
A-Class 51 65
DISABLED 65
52 A-Class 66
A-Class 53 67
54 A-Class 68
4.2.5 System Settings 69
56 A-Class 70
A-Class 57 71
58 A-Class 72
A-Class 59 73
60 A-Class 74
A-Class 61 75
4.2.6 Communications 76
A-Class 63 77
64 A-Class 78
<STX>V) is ignored 79
4.2.7 Diagnostics 80
4.2.8 MCL Options 81
4.3 Printer Messages 82
A-Class 69 83
4.4 Test Mode 84
4.4.1 Print Quality Label 84
4.4.2 Configuration Label 85
72 A-Class 86
A-Class 73 87
4.4.6 User Defined Label 88
4.4.7 Demo 88
5.1.1 Quick Calibration 89
5.1.2 Standard Calibration 90
A-Class 79 93
80 A-Class 94
A-Class 81 95
84 A-Class 98
5.2 Printhead Adjustments 99
86 A-Class 100
Printhead Assembly 101
Locking Screws 101
Adjustment Screws 101
88 A-Class 102
5.3 Printhead Replacement 103
90 A-Class 104
A-Class 91 105
92 A-Class 106
5.4 Maintenance Schedule 107
94 A-Class 108
A-Class 95 109
Head Lift Lever 110
Cleaning 110
Printhead 112
Cotton Swab 112
Access Cover 112
Peel Assembly 113
Peel Assembly Release Lever 113
Knurled Roller 114
Latch Roller 114
A-Class 101 115
WARNING 116
A-Class 103 117
104 A-Class 118
A-Class 105 119
106 A-Class 120
108 A-Class 122
A-Class 109 123
110 A-Class 124
Warning Messages: 125
Fault Messages: 126
A-Class 113 127
114 A-Class 128
TOP OF FORM FAULT 129
6.3 Hex Dump Mode 130
6.4 Resetting the Printer 131
118 A-Class 132
Specifications 133
Electrical 134
Environmental 134
Mechanical 135
Printing 135
(continued) 136
Approved Media 137
124 A-Class 138
Appendix 139
(continued) 140
A-Class 142
A-Class 129 143
Bar Code Summary Data 145
A-Class 133 147
34 567890 123 4567 148
Speed Ranges 150
A-Class 137 151
A-Class 139 153
OUTPUT SIGNALS 157
INPUT SIGNALS 157
GPIO Interface Setup 158
See WARNING message, above 159
Applicator Interface Card 160
Applicator Timing Signals 161
148 A-Class 162
A-Class 149 163
150 A-Class 164
Multi-Language Menu System 165
152 A-Class 166
A-Class 153 167
154 A-Class 168
A-Class 155 169
156 A-Class 170
158 A-Class 172
Ribbon Saver Overview 173
160 A-Class 174
Warranty Information 175
Warranty Service Procedures 176
General Warranty Provisions 176
Limitation of Liability 176
Glossary 177
164 A-Class 178
A-Class 165 179
166 A-Class 180

Comments to this Manuals

No comments

Datamax A-Class Operator's Manual Page 43

Comments to this Manuals

Related products and manuals for Bar code readers Datamax A-Class